How To Replace A Bathtub (For Newbies).
How To Replace A Bathtub (For Newbies).
Blog Article
Just how do you actually feel in relation to A Step-by-Step Guide to Installing a Bathtub?
Mounting a bathtub isn't exactly rocket science, however it does need strong plumbing, carpentry, as well as often, tiling abilities. Changing an old bath tub with a brand-new one is also a reasonably difficult job. If the old bathtub is readily obtainable, the project can move immediately; if you have to open a wall surface to get rid of the old tub as well as place the new tub, the job is much harder. In either situation, the task is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. Make certain you have actually qualified yourself for the work and also are comfortable attempting it. Instead of working with a service provider to take control of a halfway-completed project, it is better to consider employing one before you begin. Chances are you may need an expert plumber to make tube connections.
This article will help you install a new bathtub in your bathroom if you have already bought a new tub and don't require to transform the setup of your previous water supply pipelines.
Your devices and also product list ought to consist of the following:
Preparing for the Installation
First of all, the supporting frame supplied with the bath should be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make sure that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps unit to stop pressure on the bath tub.
Fit the adaptable faucet ports to the bottom of the two taps using 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Ensure you use every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom must now prepare to be suited its final placement.
Removing Old Touches
If you need to change old faucets with new ones as a part of your installment, then the first thing you need to do is detach the water. After doing so, switch on the faucets to drain any water staying in the system. The procedure of eliminating the existing faucets can be quite bothersome due to the restricted accessibility that is commonly the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipelines to the taps. Have a fabric prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, use the exact same tool to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the solitary taps from transforming during this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any old securing substance.
Before going on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Using the two wood boards under its feet, place the tub in the called for setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small points.
The following objective is to ensure that the bathtub is leveled all round. This can be accomplished by inspecting the level and also adjusting the feet on the bathtub up until the level checks out degree.
To install taps, fit all-time low of the outermost adaptable faucet connector to the appropriate supply pipe by making a compression sign up with; after that do the very same for the other tap.
Switch on the supply of water and also examine all joints as well as new pipework for leaks and also tighten them if essential. Fill the tub as well as additionally inspect the overflow outlet and the typical electrical outlet for leakages.
Ultimately, deal with the bath paneling as explained in the supplier's user's manual. Tiling and sealing around the bathtub ought to wait up until the tub has actually been made use of at the very least once as this will settle it into its final setting.
Fitting New Taps
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, then you will require reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the faucet in the placing opening in the bath/basin making certain that the washing machines remain in location between the tap and the sink. Secure the tap in place with the manufacturer given backnut. As soon as the faucet is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former type should be connected to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been connected.
Tiling Around the Bath tub
In the location where the bath meets the tile, it is essential to secure the accompanies a silicone rubber caulking. This is essential as the installation can relocate enough to fracture a stiff seal, causing the water to pass through the wall in between the bath and the tiling, causing complications with wetness as well as possible leaks to the ceiling below.
You can pick from a range of coloured sealants to blend in your components as well as fittings. They are marketed in tubes as well as cartridges, and can securing voids as much as a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always fill up the bathtub with water prior to sealing, to enable the movement experienced when the tub remains in use. The sealer can break rather early if you do not think about this movement prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof sticky and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an avid reader about How to Install a Bathtub, I assumed sharing that chunk was a good idea. Liked our entry? Please share it. Let other people discover it. We truly appreciate reading our article about How to Install a Bathtub Yourself.
Source This Article Report this page